COMPRESSOR DBX 1046V-EV

Specs.

Input Connectors : XLR and 1/4″ TRS (Pin 2 and tip hot)
Input Type : Electronically balanced/unbalanced, RF filtered
Input Impedance Balanced : > 40 kOhm, unbalanced >20 kOhm
Max Input : > +22 dBu balanced or unbalanced
CMRR Typically : >50 dB at 1 kHz
Output Connectors : XLR and 1/4″ TRS (Pin 2 and tip hot)
Output Type : Servo-balanced/unbalanced, RF filtered
Output Impedance : Balanced 30 Ohm, unbalanced 15 Ohm
Max Output : > +22 dBm balanced, > +20 dBm unbalanced
Bandwidth : 20 Hz to 20 kHz, +0/-0.5 dB
Frequency Response : 0.35 Hz to 90kHz, +0/-3 dB
Noise : < -96 dBu, unweighted, 22 kHz measurement bandwidth
Dynamic Range : > 118 dB, unweighted
THD+Noise : >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), < 0.1% any amount of compression up to 40 dB, 1 kHz
IMD : < 0.1% SMPTE
Interchannel Crosstalk : < -80 dB 20Hz to 20 kHz
Stereo Coupling : True RMS Power Summing
Compressor Threshold Range : -40 dBu to +20 dBu
Compressor Ratio : 1:1 to infinity:1
Compressor Threshold Characteristic : Selectable OverEasy® or hard knee
Compressor Attack/Release Characteristic : AutoDynamic™
Compressor Attack Time : Program-dependent
Compressor Release Time : Program-dependent
Compressor Output Gain : -20 to +20 dB
Limiter Threshold Range : 0 dBu to +24 dBu (off)
Limiter Ratio : infinity:1
Limiter Type : PeakStopPlus® two-stage limiter
Limiter Stage 1 : PeakStop® brickwall limiter
Limiter Stage 1 : Attack Time Zero
Limiter Stage 1 : Release Time Zero
Limiter Stage 2 : Predictive intelligent program limiter
Limiter Stage 2 : Attack Time Program-dependent
Limiter Stage 2 : Release Time Program-dependent
OverEasy® Switch : Activates the OverEasy compression function
I/O Meter Switch : Switches between monitoring input and output levels on the Input/Output Level meter
Bypass Switch : Activates the direct input-to-output hard-wire bypass
Operating Level Switch : (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels
ST Link Switch : Links channels in stereo pairs. Channels One and Three become the master channels
Gain Reduction Meter : 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB
I/O Meter : 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu
PeakStop™ Indicator : 1 LED to indicate PeakStop™ limiting
Function Switches : LED indicator for each front-panel switch
Output Transformer Options : Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx
Operating Voltage : Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz
Power Consumption : 20 Watts
Fuse : 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
Power Connector : IEC receptacle
Dimensions : 1.75″Hx19″Wx9″D (4.4cmx48.3cmx20.1cm)
Unit Weight : 5.2 lbs. (2.4 kg)
Shipping Weight : 7.6 lbs. (3.5 kg)